Modded Noir N1v3. 

Gateron Brown lubed with 205g0.
Stock stabs lubed with krytox 205g0
Keycaps using Pressplay Toucan XDA.

Modded Noir N1V3

Pressplay Toucan XDA

Noir N1 version 3

Gateron Brown

Black Tofu65 with DZ65rgb v2 PCB

* Brass Plate
* NK_ x Kailh Box Cream Switches (205g0 on housing and Stem, GPL 105 on Spring, 1.25mm TX Films)
* Smokey Durock v2 Stabs (205g0 on housing, Syncholube Mulitpurpose Synthetic Grease on wire)
* ePBT Spectrum Keycaps
* PE Foam on the bottom of the case
* Tempest Tape Mod

[Typing Demonstration](https://youtu.be/nnKwGFwrVn0)


Tofu65 by croatoanlp

DZ65RGB V2

ePBT Spectrum

NovelKeys x Kailh Box Cream

* Plate: nylon (custom made by Cablecar Designs)
* Stabilizers: GMK clip-in
* Switches:
  * Films: I forgot (oops)
  * Lube: Krytox VPF 1514
  * Springs: stock

Salt Rock Lamp's Prime Elise

Drop + Nephlock GMK Kaiju Custom Keycap Set

Sneakbox Designs Prime Elise

Greetech Brown

Salt Rock Lamp's 268.2

GMK Cafe

Gazzew Bobagum

Noxary 268.2

* Plate: polycarbonate (from Project Keyboard)
* Stabilizers: IDK
* Switches:
  * Film: TX standard thickness
  * Lube: Krytox GPL 105
  * Springs: stock
  * Milky tops taken from Gateron Fei Matchas

Salt Rock Lamp's QXP (#1)

Punchy Pink

Quantrik QXP

GMK Skiidata

Salt Rock Lamp's Vulcan Pro

CRP Tulip

Noxary Vulcan Pro

Cherry MX Clear

Salt Rock Lamp's Salt Rock Lamp Meme

GMK 9009

Meme

Salt Rock Lamp's LSJ Ares

LSJ Ares

EnjoyPBT Royal Alpha

* Plate: 3mm acrylic w/ foam
* Switches:
  * Kebo films
  * Lube: 3204

Salt Rock Lamp's Neuron

Walletburner Neuron

GMK Taro

Kailh Cream

* 1.5mm acrylic plate
* Stabilizers: I forgot (oops)
* Switches:
  * TX films (standard thickness)
  * Lube: Krytox GPL 3204
  * Springs: stock

Salt Rock Lamp's Noxary 268 AG

DCS White on Black

Noxary 268 AG

Gateron KS-3 Yellow

* Polypropylene plate
* Stabilizers: I forgot (oops)
* Switches:
  * TX films (standard thickness)
  * Lube: 3204
  * Springs: I forgot (oops)

Salt Rock Lamp's Prophet

CRP Peacock

Revo White

Cablecar Designs Prophet

Mounted without screws; instead, using a 1/10" layer of 40a Sorbothane under the PCB; it's tight but it just barely fits. I did this because the plate mounting points are not good on the original X60, so mounting it on Sorbothane evens everything out and adds a bit of gasket-like dampening (although not a lot due to the high compression).

* Plate: aluminum
* Stabilizers: pre-retool Cherry snap-in
* PCB: KBD6x (hotswap)
* Switches: stock (!!)

Salt Rock Lamp's Noxary X60 v1

Noxary X60

Gateron CAP Milky Yellow

GMK Hydro